Welcome Guest ( Log in | Register | Blue Circle )



Tools explained.

 
Post new topic   Reply to topic    www.bluecirlce.com Forum Index -> Off Topic
View previous topic :: View next topic  
Author Message
BlueKnight
Advanced Member


Joined: 14 Feb 2007
Posts: 1271
Location: Northumberland Straight, NB.

PostPosted: Fri Dec 09, 2011 10:58 am    Post subject: Tools explained. Reply with quote

Over the years, I have discovered these definitions/explanations to be absolutely accurate.

DRILL PRESS: A tall upright machine useful for suddenly snatching flat metal bar stock out of your hands so that it smacks you in the chest and flings your beer across the room, denting the freshly-painted project which you had carefully set in the corner where nothing could get to it.

WIRE WHEEL: Cleans paint off bolts and then throws them somewhere under the workbench with the speed of light . Also removes fingerprints and hard-earned calluses from fingers in about the time it takes you to say, 'Oh shit!'

SKIL SAW: A portable cutting tool used to make studs too short.

PLIERS: Used to round off bolt heads. Sometimes used in the creation of blood-blisters.

BELT SANDER: An electric sanding tool commonly used to convert minor touch-up jobs into major refinishing jobs.

HACKSAW: One of a family of cutting tools built on the Ouija board principle... It transforms human energy into a crooked, unpredictable motion, and the more you attempt to influence its course, the more dismal your future becomes.

VISE-GRIPS: Generally used after pliers to completely round off bolt heads. If nothing else is available, they can also be used to transfer intense welding heat to the palm of your hand.

OXYACETYLENE TORCH: Used almost entirely for lighting various flammable objects in your shop on fire. Also handy for igniting the grease inside the wheel hub out of which you want to remove a bearing race.

TABLE SAW: A large stationary power tool commonly used to launch wood projectiles for testing wall integrity.

HYDRAULIC FLOOR JACK: Used for lowering an automobile to the ground after you have installed your new brake shoes , trapping the jack handle firmly under the bumper.

BAND SAW: A large stationary power saw primarily used by most shops to cut good aluminum sheet into smaller pieces that more easily fit into the trash can after you cut on the inside of the line instead of the outside edge.

TWO-TON ENGINE HOIST: A tool for testing the maximum tensile strength of everything you forgot to disconnect.

PHILLIPS SCREWDRIVER: Normally used to stab the vacuum seals under lids or for opening old-style paper-and-tin oil cans and splashing oil on your shirt; but can also be used, as the name implies, to strip out Phillips screw heads.

STRAIGHT SCREWDRIVER: A tool for opening paint cans. Sometimes used to convert common slotted screws into non-removable screws and butchering your palms.

PRY BAR: A tool used to crumple the metal surrounding that clip or bracket you needed to remove in order to replace a 50 cent part.

HOSE CUTTER: A tool used to make hoses too short.

HAMMER: Originally employed as a weapon of war, the hammer nowadays is used as a kind of divining rod to locate the most expensive parts adjacent the object we are trying to hit. It is especially valuable at being able to find the EXACT location of the thumb or index finger of the other hand.

UTILITY KNIFE: Used to open and slice through the contents of cardboard cartons delivered to your front door; works particularly well on contents such as seats, vinyl records, liquids in plastic bottles, collector magazines, refund checks, and rubber or plastic parts. Especially useful for slicing work clothes, but only while in use.

SON-OF-A-BITCH TOOL: (A personal favorite!) Any handy tool that you grab and throw across the garage while yelling 'Son of a BITCH!' at the top of your lungs. It is also, most often, the next tool that you will need.

Hope you found this informative.
_________________
Mike
Back to top
View user's profile Send private message
Ha Boi Egg
Advanced Member


Joined: 13 Aug 2010
Posts: 467

PostPosted: Fri Dec 09, 2011 12:47 pm    Post subject: Reply with quote

LUMBER PURCHASE

Some men in a pickup truck drove into a lumberyard. One of the men walked in the office and says, "We need some four-by-twos."

The clerk replies, "You mean two-by-fours, don't you?"

The guy scratches his head and says, "I'll go check," and goes back to the truck.

He returns and says, "Yeah, I meant two-by-four."

"All right. How long do you need them?"

The guy pauses for a minute and says, "I better go check." After a while, he returns to the lumberyard and says, "A long time. We're gonna build a house."
Ba-Doom-Boom Exclamation Arrow
Back to top
View user's profile Send private message
BlueKnight
Advanced Member


Joined: 14 Feb 2007
Posts: 1271
Location: Northumberland Straight, NB.

PostPosted: Fri Dec 09, 2011 12:58 pm    Post subject: Reply with quote

Good one..!

Laughing Laughing Laughing
_________________
Mike
Back to top
View user's profile Send private message
Display posts from previous:   
Post new topic   Reply to topic    www.bluecirlce.com Forum Index -> Off Topic All times are GMT - 5 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum